OMOVAN 3-Piece Tilt-Head Stand Mixer Attachment Set

What the maker puts in writing

• “Complete 3-Pack Set– Includes 1 x K45WW wire whip, 1 x K45DH dough hook, and 1 x K45B flat beater. Made with a stainless steel wire whip and durable coated dough hook and flat beater”
• “Versatile Performance – Whip cream and egg whites with the K45WW; knead bread and pizza dough with the K45DH; and mix batters, cookie dough, mashed potatoes, and more with the K45B flat beater.”
• “Perfect Compatibility – Designed for KitchenAid Tilt-Head stand mixers. Compatible with models like K45SS, KSM75, KSM95, KSM100, KSM150PS, Artisan, Classic, Classic Plus, and more. Not compatible with bowl-lift models. Please check your mixer model before ordering.”
• “Replacement Attachments – Replaces compatible part numbers such as WP9704329, 9708471, W10674618, W10613277, and more.”
• “Everyday Kitchen Essential – Easy to install, clean, and use.”
• Title: “Compatible with 4.5-5 Qt Mixers” · Reference OM-KA-SS3-5QT

The same set as the one two dollars above it

Both publish the same three KitchenAid designations — K45WW wire whip, K45DH dough hook, K45B flat beater.

Both publish the same four part numbers replaced — WP9704329, 9708471, W10674618, W10613277.

Both publish the same compatibility list — K45SS, KSM75, KSM95, KSM100, KSM150PS.

And each has one thing the other does not.

The MEET JUICE at $21.99 has a scraper: its beater is a “K45B Coated Flat Blade Paddle with Scraper”, a flexible edge that wipes the bowl as it turns. It also names its materials — “durable stainless steel, aluminum, and anti-stick nylon coating” — where this page says only “coated”.

This has the exclusion. Bullet three ends: “Not compatible with bowl-lift models. Please check your mixer model before ordering.” The MEET JUICE says nothing of the kind, though its parts are the same tilt-head parts.

This title also carries the quart range — “4.5-5 Qt” — as does the reference, OM-KA-SS3-5QT.

So: this is the safer page and the cheaper one; that is the better beater. Two dollars for a scraper edge is a fair price if your bowl needs scraping — and see the last section for why it usually does.

Tilt-head only, and the K45 prefix says so

Fits: “K45SS, KSM75, KSM95, KSM100, KSM150PS, Artisan, Classic, Classic Plus.” Does not fit: “bowl-lift models.”

The distinction is physical. A tilt-head mixer has a head that hinges back so you lift the bowl out from underneath. A bowl-lift has a fixed head and a bowl that cranks up into it on arms. The shaft, the bowl diameter and the depth all differ, so the tools are not interchangeable — and the K45 prefix on all three designations is itself the tilt-head marker.

How the rest of this shelf answers the same question:

KitchenAid KSMVSA slicer, $69.95 — “Compatible with any KitchenAid Stand Mixer” KitchenAid KSMMGA grinder, $79.88 — “any household KitchenAid Stand Mixer power hub” KitchenAid KSMPRA pasta roller, $204.90 — “Fits all Household KitchenAid Stand Mixers” KitchenAid KSMICM ice cream maker, $96.56 — excludes seven models by name and says “verify your model number compatibility before ordering” twice New Metro Design pouring chute, $24.94 — fits “most KitchenAid, Cuisinart, Kenwood & SMEG” with metal bowls, and names four exclusions

And the reason for that spread is mechanical. A hub attachment bolts to the front power take-off, which is standardized across the whole KitchenAid range — hence “any” and “all”. A bowl tool, a bowl replacement or anything that rests on the bowl depends on dimensions that are not standardized. Which is why the cheapest and the most expensive items on this shelf are the ones with exclusions, and the three in the middle fit everything.

Three tools, three actions, and one of them is fragile

“Whip cream and egg whites with the K45WW; knead bread and pizza dough with the K45DH; and mix batters, cookie dough, mashed potatoes, and more with the K45B flat beater.”

The wire whip has many thin wires and is for folding air in: cream, egg whites, meringue, mousse, sabayon. Put it in a stiff dough and you will bend it — which is the usual way a whip dies, and the reason a replacement set like this one exists.

The dough hook is a single spiral and is for developing gluten: it folds and stretches rather than cutting, which is what bread needs. It is useless for anything light.

The flat beater is the general tool and does most of the work in most kitchens: batters, creaming butter and sugar, cookie dough, mash.

Which one is stainless matters, and this page says: “a stainless steel wire whip and durable coated dough hook and flat beater.”

That division is the right one. A whip has to be stiff and thin and goes into acidic and salty mixtures, so bare stainless is correct. A beater and a hook are better coated, because a coating stops dough sticking and keeps aluminum out of contact with food. The MEET JUICE set names what the coating is — “anti-stick nylon” over “aluminum” — and this page does not.

The coating is also the wear part. A nylon-coated beater chips at the edges after a few years, and a chipped coating on aluminum is the reason to replace a set rather than scrub it.

The bowl wall, which is what a flat beater does badly

A rigid paddle leaves a film of unmixed butter or flour against the side of the bowl, which is why you stop the mixer and scrape.

That is precisely what the MEET JUICE set addresses with its “Flat Blade Paddle with Scraper” — a flexible wiper on one or both edges that sweeps the wall as the beater orbits.

And the New Metro Design listing on this shelf makes the same point about its own separate product, with the only quantified claim anywhere here: a scraping blade “eliminates hand-scraping the mixing bowl and cuts mixing time by as much as 50%”. That figure is for a product not sold on this page, so treat it as the maker’s claim about a different item — but the mechanism it describes is real, and it is the one improvement a flat beater can have.

The other half of the same problem is the opposite direction: getting flour and sugar into the bowl without it going over the counter, which is what the New Metro pouring chute at $24.94 is for.

So the three ways to spend money on bowl work, in order: this set at $19.99 replaces worn tools; the MEET JUICE at $21.99 adds a scraper; the pouring chute at $24.94 solves the loading rather than the mixing.

What is not published

No weight. Neither three-piece set on this shelf publishes one, where every other item here does: New Metro 7.5 oz · KSMVSA 1.3 lb · KSMMGA 2.5 lb · KSMICM 6 lb · KSMPRA 7.5 lb. On a beater, weight is a proxy for how much metal is under the coating.

No coating material, as above — where the MEET JUICE names “anti-stick nylon”.

No dishwasher statement. “Easy to install, clean, and use” is the whole of it, and the shelf is unusually varied on this point: the KSMVSA publishes “All blades are dishwasher safe on the top rack”; the New Metro chute “dishwasher safe”; the KSMICM “Once the bowl has reached room temperature, simply clean with warm, soapy water”; and the KSMPRA pasta roller — the most expensive item here — “Hand Wipe only”. So the answer is not obvious by category, and a coated aluminum beater in a dishwasher is exactly the case where a detergent cycle shortens the coating’s life.

No original-part claim either way. The MEET JUICE is admirably plain — “Not OEM, but equal or better in quality” — and the three KitchenAid items all say “Genuine KitchenAid Stand Mixer Attachment - Designed and engineered by the manufacturers of the KitchenAid Stand Mixer”. This page claims neither, while listing the part numbers it replaces, which amounts to the same position as the MEET JUICE without saying so.

No capacity for the bowl-lift sizes, which follows from the exclusion: if your mixer is 5.5 or 6 quarts and bowl-lift, nothing on this shelf’s bowl-tool side fits it.

No scraper, as above.

Availability

Read on the day this page was built: $19.99 at the American Amazon shop.

Read from Keepa on the day this page was last revised; stock and price both move without notice.